Home > News > Content

Analysis Of Low Speed Machining Swing Arm Cutting Machine

Oct 10, 2017


In general, the efficiency and speed of processing with Swing Arm Cutting Machine is significantly higher than that of other thermo-cutting methods. However, in the case of the Swing Arm Cutting Machine process itself, for different shapes of cutting graphics, Need to do the appropriate increase and decrease processing, in particular, into the arc cutting stage need to keep Swing Arm Cutting Machine in the low-speed state to ensure smooth and no deformation of the cutting track. In the hot cutting process, Swing Arm Cutting Machine speed is significantly higher than the flame cutting, which also makes Swing Arm Cutting Machine way for more businesses and users love, but compared to flame cutting years of experience and mature technology , Swing Arm Cutting Machine is also slightly unfamiliar to most users, especially on the speed of the Swing Arm Cutting Machine.
In general, Swing Arm Cutting Machine at the factory, the consumer manufacturers will only provide a speed range, detailed for different materials, different thickness of the information to be cut, the user in the choice of cutting speed is also a comprehensive multi-faceted elements:
1. Swing Arm Cutting Machine model, this model for the general Swing Arm Cutting Machine machine output current size, such as 40A, 60A, 100A, 200A, etc. (of course, some imported plasma such as the German Kelbe, the United States and other parts of the brand The model is not the size of the output current for the model, here is not elaborate), depending on the size of the power of different models, select the cutting current size is different, cutting speed is not the same, you give the above data did not clarify you The choice of what brand and model Swing Arm Cutting Machine machine, it can not give detailed data;
2. Cutting the workpiece material is different, depending on the cutting material, cutting speed is also different, common cutting information: carbon steel, stainless steel cutting faster, slightly slower cast iron, followed by aluminum, the slowest is copper, Aluminum is harder to cut, cutting speed is much slower than the previous two, and the same power Swing Arm Cutting Machine copper and aluminum cutting thickness than stainless steel, carbon steel is much smaller.
In the current domestic market widely used in the Swing Arm Cutting Machine power generator configuration, the arc welding power supply with the specified thickness of the material cutting and welding processing capacity. As two completely opposite performance of the metal processing process, Swing Arm Cutting Machine power cutting and arc welding process in the relevant process also has some differences. Where Swing Arm Cutting Machine is a state in which the gas is heated to a localized ion, so that the plasma has conductivity in this state. The initial ionization of the gas is usually carried out using high-voltage generators, such as the use of argon, the ionization process is easier, because the argon is a single atom structure; and plasma arc welding is a series of heat using the compression arc Process. Plasma arc welding process to water-cooled copper alloy nozzle to form a compression arc; and Swing Arm Cutting Machine is the use of gas or water cooling form. In addition, plasma welding is also attached with a gas protection part.
Swing Arm Cutting Machine
1. Conventional Swing Arm Cutting Machine Arc welding The plasma jet generated by the traditional "dry arc compression" method can be used to weld the workpiece with or without wire solder. The welding speed is determined by the arc power and the material thickness.
2. Swing Arm Cutting Machine Arc welding The plasma arc welding and the traditional tungsten gas shielded welding process are similar in that both use Swing Arm Cutting Machine jets as a heat source to melt the material that needs to be welded, depending on the interface requirements Decided to use or not use wire solder for beads. Micro-beam plasma welding is a plasma arc melting process. This process can be in very high speed and do not use the wire solder in the case of welding meager to a few tenths of a millimeter of the material. With low current (less than 2 amps) for the advantages of plasma arc welding, arc stability, ignition is very reliable. Plasma arc welding method is also suitable for thicker sheet for multiple action welding. The process uses metal wire as solder. Swing Arm Cutting Machine The welding speed of arc welding is much higher than that of traditional tungsten gas protection welding.